Full Wave double diode detector +6db gain
Posted: Fri Apr 19, 2024 6:08 pm
Most non-FM detectors work by half-wave rectification of the RF signal, passing a stream of RF one-direction pulses that are smoothed to an AF tone.
What about the other half cycle of the perfectly good RF signal? We deliberately lose it! Duh!
This circuit uses two half-wave font ends in antiphase, so that a double sideband with or without carrier produces rectified AF from both half cycles, making a louder signal, and presumably improved SNR.
What's the downside? Two, rather than one tuned circuits and one more diode than usual.
It got me thinking that the approach would work well with other common half-wave detectors too. Could it be adapted to work with a regenerative circuit with a single tickler coupled in antiphase to each tuned circuit? The one needs to consider how to minimize the Q-damping effect of the detectors (? FETs, ?Darlingtons...) I feel an experiment coming on....
Well, what do you think?
What about the other half cycle of the perfectly good RF signal? We deliberately lose it! Duh!
This circuit uses two half-wave font ends in antiphase, so that a double sideband with or without carrier produces rectified AF from both half cycles, making a louder signal, and presumably improved SNR.
What's the downside? Two, rather than one tuned circuits and one more diode than usual.
It got me thinking that the approach would work well with other common half-wave detectors too. Could it be adapted to work with a regenerative circuit with a single tickler coupled in antiphase to each tuned circuit? The one needs to consider how to minimize the Q-damping effect of the detectors (? FETs, ?Darlingtons...) I feel an experiment coming on....
Well, what do you think?
Crystal Radio Detector Receiver High Performance Full Wave Set +6 dB Gain
OddMix.com - Technical Note - Crystal Radio - TN070417 - Karl Nagy
The radio described here is unique in that it allows quality, higher volume radio reception even in areas without any outside power. This germanium, point contact diode detector radio produces a six-decibel (6-dB) gain, which is twice the usual audio output produced by single diode sets. It does that, however, at the expense of some sleight extra work and components.
Figure 2 shows the schematic diagram of this high power version of the detector radio. This set uses two 1/4-inch coil forms with ferrite screws in each. The primary antenna coils L1 and L3 are 40 turns made with 10x0.05 MM Litz wire, taps are at the 20 turn half point. L2 and L4 are 70 turns with 10x0.05 MM Litz wire, with RF ferrite tuning screws. Their design value is 200 uH (micro Henry) for each coil. C1 and C2 are connected together, such that only one knob may be needed for tuning (a dual gang capacitor).
Parts list for high efficiency crystal detector radio:
C1 - Rotary Capacitor 500 pF - Dual unit
C2 - Rotary Capacitor 500 pF - Dual unit
C3 - Filter capacitor 1 nF, for magnetic phones only
D1 - Diode, Germanium, point contact
D2 - Diode, Germanium, point contact
L1 - Primary, Antenna coil 1 - 40 turns - tap at 20
L3 - Primary, Antenna coil 2 - 40 turns - tap at 20
L2 - Secondary coil 1 - 70 turns - 200 uH
L4 - Secondary coil 2 - 70 turns - 200 uH
R1 - Load resistor 200 K, for crystal phones only
The components and the wiring should be symmetrical as much as possible. Good soldering techniques are required. If possible, D1 and D2 should be a matched set. These diodes should also be protected against too much heat and static charge damage. A heat sink or a pair of pliers should be used on the diode leads between the solder joint and the diode body while soldering to conduct away damaging excess heat.
When starting up, close the rotary capacitor fully. Slowly rotate the capacitor to open it until the first station is found. Now rotate the slugs inside of the L1 - L2 coil form until sound volume is maximized. If the rotary capacitor has trimmer capacitors, then open the capacitor all the way, then slowly rotate it in the opposite (closed) position until the first station is found. Adjust the C1's trimmer capacitor until maximum sound volume is obtained. Fully close the capacitor and repeat the procedure from the beginning of this paragraph, until no further improvements are obtainable. Now do the same with the L3 - L4 coil. Repeat the procedure until no further improvements possible in the sound volume. Use a signal generator and an audio voltmeter is available, as they permit a much more exact alignment.
Since ferrite has higher magnetizing losses than air, an air core coil would increase the overall receiver efficiency. Because the ferrite slugs are used to equalize the two coil's inductance, the aircore coils should use bifilar winding techniques. Also, the number of turns changes, but heavier, solid wires can also be used instead of the Litze. Wound L2 and L4 with an extra wire between them. The purpose of this extra wire is to serve as a spacer. Remove this winding after the coil is completed. Wound the coil tightly unto the coil form, and secure the ends well upon completion.